Carrier 33CS420-01 El manual del propietario

7-DAY7-DAYPROGRAMMABLEPROGRAMMABLEDIGITAL DIGITAL THERMOSTAT THERMOSTAT HEATPUMPAccepts EZ ProgrammerAccepts Optional Humidity Module:Controls Humidif

CarrierPage 3.43DEHUM JUMPER SETTINGExplanation of Jumper Settings (continued)Explanation of Jumper Settings (continued)If the jumper for MISC1, MISC2

CarrierPage 3.53Y2 JUMPER SETTINGIf the jumper for MISC1 is set to Y2 the MISC1 screw terminal on the backplate will control a second stage of cooling

Page 4.1SECTION 4Wire ConnectionsWire Connections4If the terminal designations on your old thermostat do not match those on the new thermostat, refer

CarrierPage 5.1Section 5 Contents: HVAC Equipment Wiring...5.2 MISC1, MISC2, and MISC3 Wiring...5.

CarrierHPGASBOELECGAS(FAN)W1Y1GRCMISC2W2MISC1RS2RSGNDMISC3RS+5W3HUMDEHUM MISC3 MISC2 MISC1Y2(MISC1ONLY)INSTALL HUMIDITY MODULE WITH SENSINGELEMENT OUT

CarrierHPGASBOELECGAS(FAN)W1Y1GRCMISC2W2MISC1RS2RSGNDMISC3RS+5W3HUMDEHUM MISC3 MISC2 MISC1Y2(MISC1ONLY)INSTALL HUMIDITY MODULE WITH SENSINGELEMENT OUT

CarrierHPGASBOELECGAS(FAN)W1Y1GRCMISC2W2MISC1RS2RSGNDMISC3RS+5W3HUMDEHUM MISC3 MISC2 MISC1Y2(MISC1ONLY)INSTALL HUMIDITY MODULE WITH SENSINGELEMENT OUT

CarrierHPGASBOELECGAS(FAN)W1Y1GRCMISC2W2MISC1RS2RSGNDMISC3RS+5W3HUMDEHUM MISC3 MISC2 MISC1Y2(MISC1ONLY)INSTALL HUMIDITY MODULE WITH SENSINGELEMENT OUT

CarrierHPGASBOELECGAS(FAN)W1Y1GRCMISC2W2MISC1RS2RSGNDMISC3RS+5W3HUMDEHUM MISC3 MISC2 MISC1Y2(MISC1ONLY)INSTALL HUMIDITY MODULE WITH SENSINGELEMENT OUT

CarrierHPGASBOELECGAS(FAN)W1Y1GRCMISC2W2MISC1RS2RSGNDMISC3RS+5W3PROGHUMDEHUM MISC3 MISC2 MISC1Y2(MISC1ONLY)INSTALL HUMIDITY MODULE WITH SENSINGELEMENT

Page iNOTE: Due to variations in environmental conditions, it is not always possible to achieve the desired humidification or dehumidification setpoi

Page 5.85Installing the Outside SensorInstalling the Outside SensorSee the Outside Sensor accessory for further details.This wire MUST be completely s

CarrierPress the MODE button repeatedly until the HEAT icon appears on the display. Press the UP or DOWN buttons until the set temperature is 10 degr

Page 7.1SECTION 7Calibrating the Thermostat SensorsCalibrating the Thermostat Sensors7After calibration is complete, press the MODE button to return t

CarrierPage 8.1SECTION 8TroubleShootingTroubleShooting8SYMPTOM: The air conditioning does not attempt to turn on.CAUSE: The compressor timer

82136745PreparationRemove & Replace the Old ThermostatConfiguring the MISCOutputsSample Wiring DiagramsCalibrating the Thermostat SensorsTest Ope

Page 1.1SECTION 1PreparationPreparation1Assemble tools Flat BladeScrewdriverWire cutter& StripperMake sure your Heater/Air Conditioner is working

Page 2.1SECTION 2Remove & Replace the Old ThermostatRemove & Replace the Old Thermostat2Remove the cover of the old thermostat.If it does not

Carrier3Page 3.1Section 3 Contents: Configuring the Jumpers...3.2 Explanation of Jumper Settings...3.3 SECT

Carrier3Configuring the JumpersConfiguring the JumpersPage 3.2For additional flexibility, your thermostat has three configurable outputs. These outpu

CarrierPage 3.33The 3rd Stage of Heat is turned on when: (A) The 1st and 2nd stages have been on for the time required (steps 23 an