Carrier RTU OPEN 11-808-427-01 Especificaciones Pagina 43
- Pagina / 88
- Tabla de contenidos
- SOLUCIÓN DE PROBLEMAS
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
RTU Open 37
Service Test
Navigation:
i-Vu / Field Assistant:
BACview:
Properties
>
Equipment
>
Configuration
>
Service Configuration
>
Service Test
HOME
>
CONFIG
>
SERVICE
>
TEST
Service Test
can be used to verify proper operation of compressors, heating stages, indoor fan, power
exhaust fans, economizer, and dehumidification. It is highly recommended to use
Service Test
at initial
system start-up and during troubleshooting. See Appendix A: Points/Properties (page
59) for more
information.
Service Test
differs from normal operation as follows:
• Outdoor air temperature limits for cooling circuits, economizer, and heating are ignored.
• Normal compressor time guards and other staging delays are ignored.
• Alarm statuses (except
Fire
and
Safety Chain
) are ignored, but all alarms and alerts are still broadcast on
the network, if applicable.
Service Test
can be turned on or off from a BACview device, Field Assistant, or the i-Vu application. Select
Default Value
of
Enable
to turn on and
Disable
to turn off.
NOTES
•
Service Test
mode is password-protected when accessed from a BACview device.
•
Service Test
allows testing of each controller output.
•
Binary Service Test
functions are on when the
Default Value
is set to
Enable
and off when set to
Disable
.
• The output of the
Analog Service Test
is controlled by the percentage (0-100%) entered into the
Default
Value
.
• It is recommended to return every
Service Test
variable to
Disable
or
0.00
after testing each function
(unless that test variable must be active to test a subsequent function, as in
Compressor 2 Test
).
• All outputs return to normal operation when
Service Test
is set to
Disable
.
Service Test functions
• Use
Fan Test
to activate and deactivate the
Supply Fan
(BO - 1) output. Note that this output may enable
simultaneously with other
Service Test
modes even with its
Default Value
set to
Disable
.
• Use
Compressor 1 Test
to activate and deactivate the Compressor 1 (BO - 5) output. The
Supply Fan
output will be activated and deactivated in conjunction with this output. Leave
Compressor 1 Test
on
Enable
if
Compressor 2 Test
is required.
• Use
Compressor 2 Test
to activate and deactivate the Compressor 2 (BO - 4) output. Always test the
Compressor 1 output first.
Compressor 1 Test
output must be set to
Enable
for
Compressor 2 Test
to
function.
• Use the
Reversing Valve Test
to activate and deactivate the reversing valve (BO - 7) output.
• Use the
Dehumidification Test
to activate and deactivate the Humidi-MiZer™ (BO - 6) output. The Supply
Fan output will be activated and deactivated in conjunction with the Dehumidification Test output.
• Use
Heat 1Test
to activate and deactivate the Heat 1 (BO - 3) output. The Supply Fan output is activated
and deactivated in conjunction with the
Heat 1Test
output.
• Use
Heat 2Test
to activate and deactivate the Heat 2 (BO - 2) output. The Supply Fan output is activated
and deactivated in conjunction with the
Heat 2Test
output.
- Table of Contents 3
- Table of Contents 5
- RTU Open iii 5
- Introduction 7
- 2 RTU Open 8
- Specifications 9
- Safety considerations 10
- Installation 11
- To mount the RTU Open 12
- RTU Open 9 15
- 10 RTU Open 16
- Wiring specifications 17
- Wiring inputs and outputs 18
- Input wiring specifications 19
- Analog output 20
- To wire inputs and outputs 20
- Binary outputs 20
- J4 Inputs 22
- J5 Inputs 22
- J11 Outputs 23
- Wiring sensors to inputs 24
- RTU Open 19 25
- Wiring an SPT sensor 26
- RTU Open 21 27
- Wiring a CO2 sensor 30
- 26 RTU Open 32
- Wiring a Humidistat 34
- Wiring an enthalpy switch 35
- RTU Open 31 37
- Wiring a status switch 38
- Wiring a compressor safety 39
- RTU Open 35 41
- Start-up 42
- Service Test 43
- Setpoint properties 46
- 42 RTU Open 48
- Sequence of Operation 49
- Supply fan 50
- Cooling 50
- Economizer 51
- Power Exhaust 52
- Unoccupied Free Cooling 52
- Optimal Start 52
- Enthalpy control 53
- Indoor Air CO2 53
- Heating 54
- Heat Pump operation 55
- Dehumidification 55
- Demand Limiting 56
- Door contact 56
- Remote occupancy 56
- Fire Shutdown 56
- Compressor Safety 56
- Fan Status 57
- Filter status 57
- 52 RTU Open 58
- Linkage 59
- 54 RTU Open 60
- Linkage Air Source Modes 61
- Troubleshooting 62
- RTU Open 57 63
- Compliance 64
- Unit Configuration 66
- RTU Open 61 67
- 62 RTU Open 68
- Setpoints 69
- 64 RTU Open 70
- RTU Open 65 71
- 66 RTU Open 72
- Alarm Configuration 73
- Service Configuration 74
- RTU Open 69 75
- Maintenance 76
- 72 RTU Open 78
- I/O Points 79
- 74 RTU Open 80
- Single Point Linkage 81
- Device Address Binding 82
- Index 83
- RTU Open 77 83
- 78 RTU Open 84
- RTU Open 79 85
Relacionado con productos y manuales para Acondicionadores de aire del sistema de división Carrier RTU OPEN 11-808-427-01
Acondicionadores de aire del sistema de división Carrier COMFORT ZONE ZONEKIT4ZCAR Manual de usuario
(16 paginas)
(16 paginas)
Acondicionadores de aire del sistema de división Carrier OM38/40-2 El manual del propietario
(12 paginas)
(12 paginas)
Acondicionadores de aire del sistema de división Carrier Air Conditioner El manual del propietario
(28 paginas)
(28 paginas)
Acondicionadores de aire del sistema de división Carrier 30AWH008NX Manual de servicio
(138 paginas)
(138 paginas)
Acondicionadores de aire del sistema de división Carrier 30H Instrucciones de operaciones
(16 paginas)
(16 paginas)
Acondicionadores de aire del sistema de división Carrier MOTORMASTER 48/50P4 Especificaciones
(16 paginas)
(16 paginas)
Acondicionadores de aire del sistema de división Carrier 40CS024 Manual de instrucciones
(20 paginas)
(20 paginas)
Acondicionadores de aire del sistema de división Carrier 38AKS012 Guía para resolver problemas
(16 paginas)
(16 paginas)
Acondicionadores de aire del sistema de división Carrier 52PQ Guía para resolver problemas
(52 paginas)
(52 paginas)
Acondicionadores de aire del sistema de división Carrier Performance 48VR-A Manual de instrucciones
(58 paginas)
(58 paginas)
Acondicionadores de aire del sistema de división Carrier Infinity 24ANB7 Manual de usuario
(14 paginas)
(14 paginas)
Acondicionadores de aire del sistema de división Carrier 40DMC036 Manual de instalación
(28 paginas)
(28 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.118 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales